|
Pumps are sized by gallons per hour (GPH) output at one foot of lift or height. Larger capacity pumps are rated by horsepower (hp). Manufacturers offer charts that break down the power of each size pump according to incremental heights of one foot. Some companies label pumps by GPH while others assign letter or number designations that require cross-referencing to charts.
To determine the correct submersible pump for your pond, you should determine your pond's volume. It is recommended that you circulate your pond's water once at least every two hours. Hence, your pump should have GPH (gallons per hour) rating of at least half of your pond size. For example, if you had a 1000 gallon pond, then you will require a 500 GPH pump.
If you have many fish, or accessories such as fountains, waterfalls, or streams, you should account for this to be getting a larger pump (preferably one size larger). The general rule of thumb is that you should double the pump's capacity if you are planning to add fish.
Calculating the proper pump for waterfalls is a bit trickier, because waterfall pumps are rated by both GPH and maximum waterfall height. To estimate your waterfall's height, you must measure the vertical height from the top of your pump to the top of your waterfall or stream. In addition, you must add another foot of height or lift for every ten feet of hosing you will be using (this will allow for loss of volume from resistance within the hose). To calculate the required pump GPH, a general rule of thumb is that each inch of width of the channel will require an extra 100 GPH. For example, if your stream or waterfall spillway will be 10 inches wide, you will need a pump that produces an excess flow of 1000 GPH at your waterfall's height.
Troubleshooting Pump Problems the Easy WayIn any problem analysis, we have to specify the problem, check
whether there is any deviation from the normal condition,
identify the possible causes, evaluate the possible causes and
then confirm the true cause.
Pumps or other machinery will give tell tale signs when they are
not working properly. An observant pump user will be able to
avoid major breakdowns or damage if the problem is corrected early.
In order to solve any pump problem, we need to notice the
symptoms carefully so as to determine the most likely causes.
Instruments like pressure gauges are very helpful an ..
Choosing a pump that is too small will result in poor filtration and surface skimming, excessively long filter cycles and in the case of a bigger pond, poor action from the circulation jets. You must also remember that as dirt is removed by the filter, the pressure goes up, increasing dynamic head and slowing flow rate. Therefore, you must allow for that increase in pressure when choosing a pump.
Choosing a pump that is too large can result in damage to the plumbing and equipment. It can also result in cavitation, which can seriously damage the pump itself. Cavitation is the formation of bubbles in the water, very near the impeller, that occurs when the water is intensely vibrated. As the bubbles pop, shock waves are created within the pump that not only make noise but also burst with enough force to damage the impeller and other pump parts. Pressures caused by cavitation have been calculated to be in the range of 30,000 psi!
An oversized pump can also create excessive flow, which can cause erosion of the system's piping. According to NSF and IAPMO standards, the flow rate in 1 1/2-inch pipe should never exceed eight feet per second for copper and ten feet per second for PVC.
Aquarium PumpA pump is something that isn t essential in an aquarium set up
but it is desirable as this causes more oxygen for the fish. The
pump is usually attached to a long tube which is in turn
connected to a long stone that has small holes through out it;
the pump blows air into the holes creating bubbles in the
aquarium. This creates a larger surface area therefore creating
more oxygen for the fish.
It is also good for decorative purposes. Bubbles can look
attractive in a tank and also you get special statues that
require pumps, such as opening treasure chests and so on that
are used for ..
So when it comes time to buy a pump, the key factor should be performance rather than size. Determine the flow requirements of the system, then consult the pump curves provided by one or more manufacturers to choose a pump that meets your performance needs.
That way, you'll be replacing the pump truly " the numbers."
Discover the best Pump Inforamtion site on the WEB!
About the Author: David C Skul - CEO http://LinkAcquire.com" target="_blank"> http://LinkAcquire.com and Relativity, Inc. can provide global market exposure and solutions. Discover the best Pump Inforamtion site on the WEB! at http://www.pumps-inc.com/" target="_blank"> http://www.pumps-inc.com/
Source: http://www.isnare.com DAVID SKULHow To Choose A Pump
|
